 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DATA SHEET - MAY 2008 Integrated Microwave Transmitter RACK3000 0.05 - 18 GHz, 1550 nm Externally Modulated Transmitter The Emcore RACK2501 is an integrated, 1 RU high-performance transmitter with guaranteed performance over the 0.05 - 18 GHz frequency band. It incorporates a high dynamic range externally modulated transmitter and provides +6 dBm minimum of optical output power. Applications Microwave Test Cell Antenna Signal Remoting Microwave Data Links Broadband Delay-Line and Signal Processing Systems Frequency Distribution Systems The unit can be used to construct transparent optical links for microwave test cell antenna remoting, microwave signal distribution, microwave delay lines, point-to-point data links and other applications where it is necessary to transport RF and microwave signals over long distances without signal degradation. The unit operates at a nominal optical wavelength of 1550 nm. Specifications Electrical RF Connectors Frequency Range TX RF Input Power Input IP3 at 18 GHz Input P1dB at 18 GHz Noise Figure SMA (female, 50) 0.05 to 18 GHz +25 dBm, max +28 dBm, typical +25 dBm, typical 49 dB, typical 1550 6 nm SC/APC +6 to +8 dBm < 0.5 dBm over temperature and time Features Integrated externally modulated transmitter 0.05 - 18 GHz bandwidth High dynamic range 1 RU rack mount package Front panel RF and optical connections Optical Wavelength Connectors TX Optical Output Power Optical Power Stability Physical Configuration Dimensions Self Contained 1 RU Housing, 19" Rack 1.75" H x 17" W x 14" D Operating/Storage Temperature 0C to +50C Power Requirements 110 VAC @ 50W Interface and Control Front Panel Indicators Power, Link Status LED For more information on this and other products: Contact Sales at Emcore 626-293-3400, or visit www.emcore.com RACK3000 DATA SHEET - MAY 2008 Optical Characteristics Parameter Wavelength Optical Output Power Connector Return Loss Optical Connector Type Symbol PL Condition FC/APC Min 1530 6 60 Typ 1550 7 -Max 1565 8 -Unit nm dBm dB Note: In order to prevent reflection-induced distortion degradation, the laser should be connected to an optical cable having a return loss of at least 55 dB for discrete reflections and 30 dB for distributed reflections. RF Characteristics Parameter RF Input Impedance RF Return Loss 2nd Harmonic Suppression 1 dB Compression Point RF Connector Condition 9.5 RF input 0 dBm SMA (Female) Type Min Typ 50 15 -60 +25 Max -45 Unit dB dBc dBm Link Performance (Measured with 0 dBm TX RF Input and 0 dBm Optical Receiver Input) Parameter Link Gain Gain Variation Input IP3 Noise Figure Spurious Free Dynamic Range Symbol G IIP3 NF SFDR Condition @ 10 GHz 50 MHz to 18 GHz @10 GHz @ 10 GHz @ 10 GHz Typ -42 7 +28 49 98 Unit dB dB dBm dB dB/Hz2/3 Ordering Information RACK3000 Laser Safety Class IIIb Laser Product FDA/CDRH Class IIIb laser product. All transmitter versions are Class IIIB laser products per CDRH, 21 CFR 2040 Laser Safety requirements. All versions are Class 3B laser products per IEC*60825-1:1993. Maximum Power = 8 dBm Caution: Use of controls, adjustments and procedures other than those specified herein may result in hazardous laser radiation exposure. *IEC is a registered trademark of the International Electrotechnical Commission. EMCORE 2015 West Chestnut Street Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3428 www.emcore.com For more information on this and other products: Contact Sales at Emcore 626-293-3400 or visit www.emcore.com (c) Copyright 2008, Emcore Corporation |
Price & Availability of RACK3000
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |